Milk Line Washing Components Farm Supplies For Sale In Philadelphia

High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120116 Jetter Cups for Surge. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts.

BUY BULK! FREE SHIPPING! Black rubber Duck Bill-style Drain Valve is used with CIP assemblies and moisture traps.

Black rubber Duck Bill-style Drain Valve is used with CIP assemblies and moisture traps.

Timer Control Module features electro-mechanical timing, failsafe timer, standard 8-minute wash cycle, 24-hour clock for automatic pre-sanitizing, door interlock and is CSA-approved.

Summit E Programmer is used to control the #1209838 Three-Pump Peristaltic Pump to automate and improve accuracy of dairy sanitation chemical dispensing. Programmer can set a variety of adjustments including on/off, run times and delay times from 1 second...

Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head. Replaces Milk-Rite 7102.

This smooth, white Tee is made out of food-grade plastic.

Three-Jar Dispenser includes hot and cold water valves, 25 ft. Of water hose, and sink bracket. Three-Jar Dispenser may be combined with the Timer Control Module to make a complete pipeline wash system.

Coburn"s S.S. Distributor Tee with vent hole is smooth and clean throughout for efficient water flow. Tubes are aligned for ease and convenience of hose handling.

CIP Thermometer is used to make sure the CIP wash solution is at the required 160F degrees at the start of the wash cycle. Thermometer has a recalibration feature and includes a plastic carrying case.

Concentric Reducing Ferrule reduces from 2" to 1-1/2" tube and is 1-1/8" long.

Improved Sentinel Air Injector activates at a minimum of 5" of vacuum, has a capacity of 200 cubic feet of air per minute on 15" of vacuum, and can be easily adjusted. Wall or direct-mounted, air injector operates on 120 volts.

Concentric Reducing Ferrule reduces from 3" to 2" tube and is 1-5/16" long.

Butt weld bevel-seat ferrule for 2-1/2" tubing is 27/32" long and B-dimension of 2-29/32" and C-dimension of 2-23/64".

External Seal Kit for LC Thomsen Model #4 Milk Pump includes head O-ring, 2 impeller clips, ceramic seal and rotary seal assembly. Original equipment kit.

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends. Reducer from 4" OD to 2" OD tube is 8" long.

Clamp end tee for 2-1/2" tube has A-dimension of 3-1/2" and B-dimension of 7".

Bevel-seat recessless ferrule for 2-1/2" tubing is 1-1/2" long.

Glass-to-Stainless Steel Ferrule with Gasket Groove is made of Type 304 Stainless Steel with #4 Dairy Finish. 3/4" long for 1.5" OD tube.

90 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends. Elbow for 1" OD tube features inner radius of 1.5" and center distance (C) of 2".

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends. Reducer from 4" OD to 1.5" OD tube is 10" long.

Solid End Cap for Tri-Clover line is made of Type 304 Stainless Steel with #4 Dairy Finish. End cap for 2.5" OD tube has 3.05" OD.

Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features threading on one end and butt weld on the other. Ferrule for 3" OD tube is 29/32" long.

Black Gasket, (top under slide) 9/16".

Solid End Cap for Tri-Clover line is made of Type 304 Stainless Steel with #4 Dairy Finish. End cap for 3" OD tube has 3.58" OD.

Replacement pump tube with fittings, 8" piece."