Used Equipment Loader And Skid Steer Attachments For Sale In Wittenberg

Cummins 5.9LT eng, 4 spd powershift trans, 3 piece tubeless wheels, hyd brakes, hyd artic steering, 8' 3" bucket width/2.5 yard cap, 8' 3" wide, 11' 3" tall, 22' 6" long, 26,000# machine, about 6,000# cap, hyd quick coupler, hyd 4 in 1 bucket, heat

4 cyl New Holland turbo dsl eng, 8 spd shuttle trans, hyd brakes, hyd/4 wheel steer, 97" loader bucket/2 yard, 25" backhoe bucket, 17'6" dig depth, 20,500# machine, about 6,000# cap, joystick controls, front & back aux hyds, 4 wheel steer, 4x4

23,000# machine, 8'5" hyd quick-tach bucket, 2.5 cu yrd capacity, Cat 3204 turbo dsl, articulating 4 spd powershift, air brakes, 2 line aux hyds, enc cab

Case A504 BDT dsl eng, shuttle trans, steel/3 piece wheels, air over hyd brakes, hyd steering, 8' 7" wide, 21' long, 11' 1" tall, about 23,000# machine, approx 60 gallon fuel tank, 3 yard bucket

6 cyl Nissan turbo dsl eng, 4 spd shuttle trans, 3 piece/tubeless wheels, air over hyd brakes, hyd steering, about 4 yard bucket cap, 10' 2" wide, 11' 7" tall, 30' long, about 44,000# machine, about 12,000# cap, heat, good cutting edge

36" wide, 10 1/4" inside mount (260MM), 15" pin to pin, 2 3/8" pin dia (60MM)

18" wide, 8 3/4" inside mounts, 16" pin to pin, 2 1/2" pin dia, Fits Cat 312 & others, 3 teeth, side cutters

Standard skidsteer quick tach, serrated teeth, 2 line hydraulics, 46" wide, 27" high, 33" long

18" wide, 13 1/2" inside mounts, lightly used, v bottom, black in color, quick tach mounts

17" stick width, 3 15/16" pin dia, 21" pin spacing, replaceable tooth

39" wide, 3 1/8" pin diameter, 12 3/4" stick width

12' wide, 7' 6" deep, 5' 7" tall, 49" center to center lift arms, 3.5 top pin diameter, 4.25 lower pin diameter, 3.5 boss width, 8 teeth (like new) spade nose, came off a Clark Michigan 275C loader

65MM pins, 255" inside mounts, approx 2 1/2" - 2 9/16" pins, 10" inside mounts, 15" pin to pin, 31" wide, 5 teeth

88" wide, 84" sweep width, hyd angling, spring loaded, excellent broom cond, mech kick stand, skidsteer quick tach, 2 line hyds

11' rock/root rake, 5 teeth, w/outside mount arms

24" wide, 9 1/8" inside mounts, 2 3/8" pin dia, 15" pin to pin, 4 teeth, used/good condition, rear lifting eye

12" wide, 10 1/4" stick, 9 3/4" curl cyl, 14" pin to pin, 2" stick pin dia, 1 3/4" curl pin dia, 3 teeth

SKIDSTEER BUCKET, 72" WIDE, 32" DEEP, 20" TALL, WELD ON CUTTING EDGE, STANDARD SKIDSTEER COUPLER

50" wide, 15 1/4" stick width, 3 1/2" pin diameter, 19 1/2" center to center

60" wide, 5 1/2 x 3" bottom wear plates, universal quick tach, designed for loaders w/1,300# cap, gray in color, new

13' 6" wide, quick tach mounts, spring loaded cutting edge.

10' 1" wide, 43" tall, 8' long, very low hrs of use, came off a JD 700J dozer, reversable cutting edge

Forklift mast w/cylinder & carriage, 3 stage

39" wide, 12 1/4" inside mounts, 17 1/2" pin to pin, 3 1/8" pin dia, 5 teeth w/ welded on smooth edge, rear lifting eye, very good condition

SKIDSTEER BUCKET, 72" WIDE, 32" DEEP, 20" TALL, WELD ON CUTTING EDGE, STANDARD SKIDSTEER COUPLER

80mm pins, 311 mm inside mounts, 12 1/4" inside mounts, 3 1/8" pin diameter, 18 1/8" pin to pin, 45" wide, 5 teeth, yellow in color

Set of 2 rails w/pads & 2 idlers, 40 links, 24" pads, 30%