Used Equipment John Deere Precision Ag Equipment For Sale In Campbellton

Field ready Front Disk Blade Size: 23, Rear Disk Blade Size: 24, Walking Tandems 29'3", rock flex, rear hitch and hydraulics for crumbler, hydraulic fore/aft, walking tandems, 23" front and 24" rear blades.

18' flex, 3" cut, Stainless floor, Sprocket drive, Poly, Good auger and floor, Dividers taken off for transport

Can convert back to sprocket drive if needed Deck Plates: Manual, Field Ready, Snout Type: Metal, Telescoping Drive 6R36, dry drive, CM shafts, straight tin, We leased this head out in fall of 2017 to cut 300 acres with no problems.

21x7, double disc, double run, good blades Disc Opener Type: Double, Drill Type: Pull, Field Ready, Number of Openers: 21

20' flex, 3" cut, sprocket drive. Dividers taken off for transport. Good auger and floor. Cart not included Very sharp head for year.

Head only, no cart Deck Plates: Manual, Field Ready, Snout Type: Metal, Stalk Stompers: 2 4R36, high tin, dry drive, dual sprocket drive, stalk chompers, sprockets and chain are fair/good.

Or $11,000 for pair 385/65R22.5 tires, brakes, slip tounge, light kit, double doors, (2) available, $6,000 ea.

500 bu, corner auger, large 1000 pto, clean cart.

15' no-till or drill can be detached for use as a 3pt. Very sharp drill, Field ready Conventional drill , 22x8, press, double disc, Yetter hyd. Markers, great blades and coulters, only showing 6197 acres on counter.

30', sliding tounge, unit was a demo, like new

Gravity wagons, several in stock, Starting @ $1,250.

Good 15' flex head, 3" cut, poly tines, dividers, (3) Available.

All bought new at same time w/ consecutive serial numbers, slip tounges, all metal, no wood, great rubber, light kits. Good clean wagons with very little use. Or 8,500 for pair.

Wings taken off for transport Deck Plates: Manual, Outer Side Shield, Snout Type: Metal Clean hard-to find head. Will fit K or K2 machine.

Good clean 20' drill set up for soybeans, 20x15, planter units, V-press, hydraulic markers, spray bar, 3 pt.

21x7, double disc, 3" press, cylinder Disc Opener Type: Double, Drill Type: Pull, End Wheels, Field Ready, Number of Openers: 21

6RW, hyd fold, hyd pump,

500 gallon, 45' booms, 3 way nozzles, foamers, walking tandems, pto pump, manual lift, no controls Foam

Wings off for transport Deck Plates: Manual, Outer Side Shield, Snout Type: Metal 2R30, very clean hard-to-find head. Off K2 combine.

Good 15' flex head, 3" cut, metal tines, (3) Available.

We bought this tractor from Ohio 7 years ago and have been using on our farm to pull 12' offset and 12' box blade, we have put about 300 hrs on it. Cab, Air, Heat, Radio, Forward Speed: 8, Front Tire % Remaining: 30, Front Tire Size: 28.1-26, Front Tire...

Has stalk chomper, Field ready 4R36, Great chains, sprockets, rollers, knives, floor and tin.

Straight head w/ good tin. Head only, no cart! Deck Plates: Manual, Telescoping Drive Dual jackshafts, Good rollers, chains, sprockets and knives. Head has been test run and sounds good.

Standard rotor, beater, cummins engine, reverser, GLM, new a/c compressor w/ cold air, 1-owner, This is the one of the cleanest machine's we have had in a long time. Original paint w/ no polish needed.

45' booms, 3 way nozzles, foamers, controls, pto pump, hydraulic lift, single axle, mix tank Foam

Fore/aft, single drive, dividers, (3) Available. 20' flex head w/ 3" cut, tear drop reel, hyd.

3" cut, pipe reel, double drive, grain grabbers, dividers, good floor and auger, head only, no cart