Used Equipment John Deere Combines For Sale In Huron

PRWD, CONTOUR MASTER, 650/85R38 DUALS, 750/65R26, GRAIN LOSS MONITOR, ROCK TRAP, 26' UNLOAD AUGER, POWERCAST TAILBOARD, 3 SPEED ELECTRICAL SHIFT TRANSMISSION, GENERAL PURPOSE EXTENDED WEAR PACKAGE, ROTOR EXTENDED WEAR, REGULAR WEAR GRAIN HANDLING, PREMIUM...

2WD, PRO DRIVE, 650/85R38 FS DUALS, 600/65R28 FS, POWERCAST TAILBOARD, EXTENDED WEAR, VSFH, MAURER M120 TIP UP, ROUND BAR AND SMALL WIRE CONCAVES. Combine Type: Corn/Bean Duals/singles: Singles Chopper/spreader: Chopper Header: No Premier Cab Contour-Master...

I am looking for a 15 or 20 foot JD 1590 no-till drill with marker arms and dolly wheel. I am looking for a good used John Deere no-till drill with marker arms and dolly wheel. I am located in Michigan

1-19/24R30/FXFLD/VAC Metering System: Vacuum Row Command: Yes blades measure 14 3/4, active pdf, row command, markers, liquid fertilizer with 500 gallon tank, rate controller, John blue pump, redballs Dawn floating trashwhippers, 1 Dawn curvetine per...

PS/48080R50DLS/PTO/PS/5SCV/DLXCP

24R30/WFLD/CCS/VAC Metering System: Vacuum Row Command: Yes Central Commodity System Category IV Drawbar Hitch Variable Rate Drive with Three Hydraulic Motors and Three Section Disconnect Pro-Shaft Drive with MaxEmerge 5 Row Units with RowCommand Clutches...

24R30/WFLD/VAC/CCS Metering System: Vacuum Central Commodity System Category IV Drawbar Hitch Variable Rate Drive with Three Hydraulic Motors and Three Section Disconnect Pro-Shaft Drive with MaxEmerge 5 Row Units with RowCommand Clutches Regular Duty...

MFWD/20 SPD PQ/540/1000 PTO/3 SCVS

24R30/WFLD/VAC/CCS Metering System: Vacuum Row Command: Yes Central Commodity System Category IV Drawbar Hitch Variable Rate Drive with Three Hydraulic Motors and Three Section Disconnect Pro-Shaft Drive with MaxEmerge 5 Row Units with RowCommand Clutches...

Price Includes 620R loader, bucket, grapple

35'/Flex/Poly/CM/LOW STONE DAM/LANKOTA DIVIDERS Auger with full width fingers PlatformLength: 35 Feet Platform Type: Flex

2013 JOHN DEERE 640FD PlatformLength: 40 Feet Platform Type: Flex

35'/FLEX/SinglePT single point, JD dividers Auger with full width fingers PlatformLength: 35 Feet Platform Type: Flex

12R30”, KNIFE ROLLS, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER, AUTO HEADER HEIGHT, CHOPPING, OPPOSED KNIFE STALK ROWS, AUTOTRAC ROWSENSE SENSORS, LANKOTA STALK STOMPERS 12R30”, KNIFE ROLLS, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR...

12R30”, KNIFE ROLLS, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER, AUTO HEADER HEIGHT, OPPOSED KNIFE ROLLS, AUTOTRAC ROWSENSE FEELERS 12R30”, KNIFE ROLLS, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER, AUTO HEADER HEIGHT, OPPOSED KNIFE...

12R20”, NON-CHOPPING, KNIFE ROLLERS @ 50%, HYDRAULIC DECK PLATES, HEADER HEIGHT SENSING, ROW SENSE REELERS, STUBBLE LIGHTS 12R20”, NON-CHOPPING, KNIFE ROLLERS @ 50%, HYDRAULIC DECK PLATES, HEADER HEIGHT SENSING, ROW SENSE REELERS, STUBBLE LIGHTS Chopping...

24R30/WFLD/CCS/VAC

12R30”, KNIFE ROLLS, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER, AUTO HEADER HEIGHT, OPPOSED KNIFE ROLLS, AUTOTRAC ROWSENSE FEELERS 12R30”, KNIFE ROLLS, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER, AUTO HEADER HEIGHT, OPPOSED KNIFE...

18R20”, KNIFE ROLLS, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER, AUTO HEADER HEIGHT, CHOPPING, ROWSENSE, SINGLE POINT, SHIPPING IS AVAILABLE. 18R20”, KNIFE ROLLS, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER, AUTO HEADER HEIGHT,...

John Deere 8520 Tractor, Front & Rear Duals, 3 Point, Weights

12R30”, KNIFE ROLLS, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER, AUTO HEADER HEIGHT, OPPOSED KNIFE ROLLS, AUTOTRAC ROWSENSE FEELERS 12R30”, KNIFE ROLLS, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER, AUTO HEADER HEIGHT, OPPOSED KNIFE...

12R20”, KNIFE ROLLS 50%, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER DRIVES, AUTO HEADER HEIGHT, NON-CHOPPING, ROW SENSE FEELERS 12R20”, KNIFE ROLLS 50%, HYDRAULIC DECK PLATES, STUBBLE LIGHTS, CONTOUR MASTER DRIVES, AUTO HEADER HEIGHT, NON-CHOPPING,...

1-19/60'10/SNGL/48080R42/550TBH Shoot: Single Shoot front and rear blades measure 6 inches from hub (85%), mud smith gauge wheels intelligent Ag blockage 480/80R42 GY duals @ 60%, hydraulic drive, black, green, and yellow rollers Single Shoot Air Package...