New Equipment Construction Attachments For Sale In Wittenberg

59" tall, 48" wide, 73" long, tinted glass, interior light, wiper motor, black in color

Set of rubber tracks, 42 links/pins, 10" wide, about 55" long

New post hole auger, 10" diameter auger, 50" auger length, quick tach to skidsteer, quick couple hoses, motor saddle support or dangle

8 3/4" stick width, 2 1/2" pin diameter, 24" wide, 4 teeth, bold on side cutters

70" wide, 3 point hookup, PTO driven

42 links/pins, 10" wide, about 55" long

Roto Tiller, 84" wide, 3 point hookup, PTO driven, adjustable skid plates for depth control

48" forks, 45" carriage, 40" back height, 4,000# capacity, skidsteer quick-tach, mechanical sliding forks, walk through cut out

24" bucket, 6 1/2" stick width, 11" or 15" center to center, 1 3/4" pins, black in color

Grapple bucket, 6' 10" wide, 2" pin hole, 41 1/2" between ears, quick disconnedt, dual grapple & cylinder

36" wide, 10 1/4" inside mount (260MM), 15" pin to pin, 2 3/8" pin dia (60MM)

18" wide, 8 3/4" inside mounts, 16" pin to pin, 2 1/2" pin dia, Fits Cat 312 & others, 3 teeth, side cutters

Standard skidsteer quick tach, serrated teeth, 2 line hydraulics, 46" wide, 27" high, 33" long

18" wide, 13 1/2" inside mounts, lightly used, v bottom, black in color, quick tach mounts

17" stick width, 3 15/16" pin dia, 21" pin spacing, replaceable tooth

39" wide, 3 1/8" pin diameter, 12 3/4" stick width

12' wide, 7' 6" deep, 5' 7" tall, 49" center to center lift arms, 3.5 top pin diameter, 4.25 lower pin diameter, 3.5 boss width, 8 teeth (like new) spade nose, came off a Clark Michigan 275C loader

65MM pins, 255" inside mounts, approx 2 1/2" - 2 9/16" pins, 10" inside mounts, 15" pin to pin, 31" wide, 5 teeth

88" wide, 84" sweep width, hyd angling, spring loaded, excellent broom cond, mech kick stand, skidsteer quick tach, 2 line hyds

11' rock/root rake, 5 teeth, w/outside mount arms

24" wide, 9 1/8" inside mounts, 2 3/8" pin dia, 15" pin to pin, 4 teeth, used/good condition, rear lifting eye

12" wide, 10 1/4" stick, 9 3/4" curl cyl, 14" pin to pin, 2" stick pin dia, 1 3/4" curl pin dia, 3 teeth

SKIDSTEER BUCKET, 72" WIDE, 32" DEEP, 20" TALL, WELD ON CUTTING EDGE, STANDARD SKIDSTEER COUPLER

50" wide, 15 1/4" stick width, 3 1/2" pin diameter, 19 1/2" center to center

60" wide, 5 1/2 x 3" bottom wear plates, universal quick tach, designed for loaders w/1,300# cap, gray in color, new

13' 6" wide, quick tach mounts, spring loaded cutting edge.

10' 1" wide, 43" tall, 8' long, very low hrs of use, came off a JD 700J dozer, reversable cutting edge