Milk Line Washing Components Milking Equipment For Sale In Texas

Black rubber Duck Bill-style Drain Valve is used with CIP assemblies and moisture traps.

Diverter Plug for 2" Glass Tee.

Coburn"s Black Plastic Distributor Tee is smooth throughout for efficient water flow and is an economical alternative to the Stainless Steel Distributor Tee.

Short round wash and milk shut-off plug for 3a" line.

Long round wash and milk shut-off plug for 3a" line.

Drain valve assembly mounts directly to the wash vat drain fittings with a no-hub coupling (available separately). 50-60 Hz, .31 amp. May be plumbed directly to the drain. 115VAC with drip-proof motor enclosure.

Thermometer registers from 1 to 220F and the face is 1" diameter with a 5" stainless steel stem. CIP Thermometer is used to make sure the CIP wash solution is at the required 160F degrees at the start of the wash cycle.

Use the Coburn stainless steel claw hanger whenever you need to hang a Delaval or other style claw upside-down. Ideal for storage and cleaning in place, this claw hanger includes hangar and U-bolt for installation on stall tubing.

Shut-off plugs and parts available separately. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Coburn"s S.S. Distributor Tee is smooth and clean throughout for efficient water flow. Tubes are aligned for ease and convenience of hose handling.

Coburn"s S.S. Distributor Tee with vent hole is smooth and clean throughout for efficient water flow. Tubes are aligned for ease and convenience of hose handling.

Bender Diverter Valve - 120V

This smooth, white Tee is made out of food-grade plastic.

Capacity, switch setting to program pump run time, hot and cold water valves, cycle timer and is CSA-approved. Three-Pump Dispenser features three motor-driven peristaltic pumps each with 300 oz.

Butt weld bevel-seat ferrule for 4" tubing.

Stainless Steel Fit ‘em All Jetter Rack will hold virtually any milking claw including Delaval. Jetter Rack is sold individually, or as part of complete kit. The 120112 has rounded insert for holding the jetter cups.

90 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends. Elbow for 2.5" OD tube features inner radius of 3.75" and center distance (C) of 4.25".

Shut-off plugs and parts available separately. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Seal Kit f/New-Style Westfalia Milk Pump

Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features a standard clamp on one end and butt weld on the other. Ferrule for 2" OD tube is 1/2" long with 1.870" ID.

Concentric Reducing Ferrule reduces from 2" to 1-1/2" tube and is 1-1/8" long.

Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features a standard clamp on one end and butt weld on the other. Ferrule for 1.5" OD tube is 1/2" long with 1.375" ID.

2" Blue Plastic Milk Valve features a 5/8" inlet.

Teflon Tri-Clamp Gasket.

Timer Control Module features electro-mechanical timing, failsafe timer, standard 8-minute wash cycle, 24-hour clock for automatic pre-sanitizing, door interlock and is CSA-approved.

Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head. Replaces Milk-Rite 7100.