Milk Line Washing Components Milking Equipment For Sale In Pennsylvania

Bender Diverter Valve - 240V

Long round wash and milk shut-off plug for 2" line.

Shut-off plugs and parts available separately. 3" Wash Valve weighs 3 lbs. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks...

Black rubber Duck Bill-style Drain Valve is used with CIP assemblies and moisture traps.

Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head. Replaces Milk-Rite 7102.

Capacity, switch setting to program pump run time, hot and cold water valves, cycle timer and is CSA-approved. It may be combined with the 8950 Timer Control Module for more functionality.

This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120116 Jetter Cups for Surge. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts.

Hardware is included. CIP components are sold individually, or as part of complete kit. Stainless Steel Fit ‘em All Heavy Duty Jetter Rack will hold virtually any milking claw including Delaval.

Thermometer registers from 1 to 220F and the face is 1" diameter with a 5" stainless steel stem. Thermometer has a recalibration feature and includes a plastic carrying case. CIP Thermometer is used to make sure the CIP wash solution is at the required...

Internal Seal Kit for LC Thomsen Milk Pump. Includes 3 shaft O-rings, 1 head O-ring, 1 rotary seal spring, 1 teflon rotary seal and 2 impeller clips.

90 Degree tube bend for 2" tube OD features "A" dimension of 4-1/16". Type 304 Stainless Steel.

Long round wash and milk shut-off plug for 3a" line.

Bend for 1" OD tube features "B" dimension of 1.888". Bend for 2" OD tube features "B" dimension of 2-5/16".Bend for 2.5" OD tube features "B" dimension of 3".Bend for 3" OD tube features "B" dimension of 3".Bend for 4" OD tube features "B" dimension...

Clamp-end Special Y for 2" tube OD features "A" dimension of 3-1/2" and "B" dimension of 7". Type 304 Stainless Steel.

180 Degree butt-weld U-bend for 2.5" tube OD features "A" dimension of 7-1/2". Type 304 Stainless Steel.

Diverter Plug for 2" Glass Tee.

Replacement pump tube with fittings, 8" piece."

Rubber gasket with #10 mesh stainless steel screen for 1.5" ID Tube

Heavy duty Drawer-Style Stainless Steel Jetter Rack includes nuts and bolts for mounting. Fits all claws including DeLaval.

45 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends. Elbow for 4" OD tube features "C" dimension of 3-1/8".

Bevel-seat recessless ferrule for 4" tubing is 1-5/8" long.

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and featuresstandard clamp fitting on both ends. Reducer from 4" OD to 2" OD tube is 9-1/8" long.

Extra heavy cross clamp fits two pieces of 2-3/8" tubing.

Butt weld bevel-seat ferrule for 4" tubing.

Drain valve assembly mounts directly to the wash vat drain fittings with a no-hub coupling (available separately). 115VAC with drip-proof motor enclosure. May be plumbed directly to the drain.

Bevel-seat recessless ferrule for 2" tubing is 1-3/8" long.

Teflon bevel seat gasket for 1.5" OD tubing.