Milk Line Washing Components Milking Equipment For Sale In Connecticut

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation. This CIP Assembly for DeLaval and IBA features Drawer-Style Stainless Steel Jetter Rack and 120115 jetter cups.

Bender Diverter Valve - 240V

Black rubber Duck Bill-style Drain Valve is used with CIP assemblies and moisture traps.

Tubes are aligned for ease and convenience of hose handling. Coburn"s S.S. Distributor Tee with vent hole is smooth and clean throughout for efficient water flow.

3" Wash Valve weighs 3 lbs. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Of water hose, and sink bracket. Three-Jar Dispenser includes hot and cold water valves, 25 ft. Three-Jar Dispenser may be combined with the Timer Control Module to make a complete pipeline wash system.

Tubes are aligned for ease and convenience of hose handling. Coburn"s S.S. Distributor Tee is smooth and clean throughout for efficient water flow.

Long round wash and milk shut-off plug for 2" line.

Long round wash and milk shut-off plug for 3a" line.

4" Wash Valve weighs 5 lbs. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Short round wash and milk shut-off plug for 3a" line.

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts. This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120116 Jetter Cups for Surge.

1-1/8" long for 3" OD Tube. Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish.

Seal Kit f/New-Style Westfalia Milk Pump

Bevel-seat recessless ferrule for 2-1/2" tubing is 1-1/2" long.

Reducer from 2.5" OD to 2" OD tube is 2" long. Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends.

Butt weld end tee for 4" tube has L-dimension of 3-7/8" and B-dimension of 7-3/4".

Replaces Milk-Rite 7100. Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head.

Elbow for 3" OD tube features inner radius of 4.5" and center distance (C) of 5". 90 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends.

Type 304 Stainless Steel. 180 Degree butt-weld U-bend for 2.5" tube OD features "A" dimension of 7-1/2".

Ferrule for 1.5" OD tube is 1/2" long with 1.375" ID. Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features a standard clamp on one end and butt weld on the other.

Repair Kit contains 1 each VH1001 Carbon Seal, VH1002 Ceramic Seal, VH1003 O-Ring, VH1004 4" Gasket new-style and VH1011 4" Gasket old-style.

Programmer can set a variety of adjustments including on/off, run times and delay times from 1 second to 45 minutes. Summit E Programmer is used to control the #1209838 Three-Pump Peristaltic Pump to automate and improve accuracy of dairy sanitation chemical...

The 120112 has rounded insert for holding the jetter cups. Stainless Steel Fit ‘em All Jetter Rack will hold virtually any milking claw including Delaval. Jetter Rack is sold individually, or as part of complete kit.

Not recommended for applications where pressure exceeds 150 psi. This high-quality butterfly valve for 4" tube is made of type 316 Stainless Steel for clamp connection.

Extra heavy cross clamp fits two pieces of 2-3/8" tubing.

Flange is 6" in diameter. Stainless Steel Wall Flange for 3" is also available for 1.5", 2", 2.5" and 4" tubing.