Milk Line Washing Components Milking Equipment For Sale In Charlotte

Capacity, switch setting to program pump run time, hot and cold water valves, cycle timer and is CSA-approved. Three-Pump Dispenser features three motor-driven peristaltic pumps each with 300 oz.

Long round wash and milk shut-off plug for 2" line.

Black rubber Duck Bill-style Drain Valve is used with CIP assemblies and moisture traps.

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation. This CIP Assembly for DeLaval and IBA features Drawer-Style Stainless Steel Jetter Rack and 120115 jetter cups.

Bender Diverter Valve - 120V

Replacement pump tube with fittings, 8" piece."

Long round wash and milk shut-off plug for 2" line.

Hardware is included. Stainless Steel Fit ‘em All Heavy Duty Jetter Rack will hold virtually any milking claw including Delaval. CIP components are sold individually, or as part of complete kit.

Programmer can set a variety of adjustments including on/off, run times and delay times from 1 second to 45 minutes. Summit E Programmer is used to control the #1209838 Three-Pump Peristaltic Pump to automate and improve accuracy of dairy sanitation chemical...

Bevel-seat recessless ferrule for 4" tubing is 1-1/2" long.

Butt weld bevel-seat ferrule for 2" tubing is 23/32" long and B-dimension of 2-3/8" and C-dimension of 1-55/64".

Intake orifice is 1-1/2". Improved Sentinel Air Injector activates at a minimum of 5" of vacuum, has a capacity of 200 cubic feet of air per minute on 15" of vacuum, and can be easily adjusted.

May be plumbed directly to the drain. 115VAC with drip-proof motor enclosure. 50-60 Hz, .31 amp. Drain valve assembly mounts directly to the wash vat drain fittings with a no-hub coupling (available separately).

Tubes are aligned for ease and convenience of hose handling. Coburn"s S.S. Distributor Tee is smooth and clean throughout for efficient water flow.

Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features threading on one end and butt weld on the other.Ferrule for 2" OD tube is 23/32" long.

End cap for 4" OD tube has 4.5" OD. Solid End Cap for Bevel Seat is made of Type 304 Stainless Steel with #4 Dairy Finish.

Elbow for 1" OD tube features inner radius of 1.5" and center distance (C) of 2". 90 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends.

Ferrule for 2.5" OD tube is 27/32" long. Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features threading on one end and butt weld on the other.

Rubber tri-clamp gasket for 3" OD tubing.

Not recommended for applications where pressure exceeds 150 psi. This high-quality butterfly valve for 2.5" tube is made of 304 Stainless Steel for clamp connection.

Shut-off plugs and parts available separately. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

5/8" Stainless Steel Reversed Gooseneck fits 150200A Sliding Milk Valve.

End cap for 2.5" OD tube has 3.05" OD. Solid End Cap for Tri-Clover line is made of Type 304 Stainless Steel with #4 Dairy Finish.

Butt weld end tee for 4" tube has L-dimension of 3-7/8" and B-dimension of 7-3/4".

Includes Gaskets and Seal to repair old-style Delaval Milk Pump.

Reducer from 4" OD to 3" OD tube is 4" long. Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends.

Seal Kit f/BouMatic Milk Pump