Milk Line Washing Components Farm Supplies For Sale In Kentucky

This CIP Assembly for DeLaval and IBA features Stainless Steel jetter rack and 120115 jetter cups. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation.

Bender Diverter Valve - 120V

This CIP Assembly for BouMatic features Stainless Steel jetter rack and 120117 jetter cups. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation.

Long round wash and milk shut-off plug for 2" line.

Hardware is included. Jetter Rack is sold individually, or as part of complete kit. The 120112 has rounded insert for holding the jetter cups. Stainless Steel Fit ‘em All Jetter Rack will hold virtually any milking claw including Delaval.

This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120115 Jetter Cups for DeLaval and IBA. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts.

Replacement pump tube with fittings, 8" piece."

Coburn"s Black Plastic Distributor Tee is smooth throughout for efficient water flow and is an economical alternative to the Stainless Steel Distributor Tee.

This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120117 Jetter Cups for Boumatic. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts.

Summit E Programmer is used to control the #1209838 Three-Pump Peristaltic Pump to automate and improve accuracy of dairy sanitation chemical dispensing. Programmer can set a variety of adjustments including on/off, run times and delay times from 1 second...

RFE Silicone Grease f / Peristaltic Pump Tubing. Silicone Grease (Required when replacing Peristaltic Pump Tubes)

Coburn"s S.S. Distributor Tee is smooth and clean throughout for efficient water flow. Tubes are aligned for ease and convenience of hose handling.

High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Three-Pump Dispenser features three motor-driven peristaltic pumps each with 300 oz. Capacity, switch setting to program pump run time, hot and cold water valves, cycle timer and is CSA-approved.

Use the Coburn stainless steel claw hanger whenever you need to hang a Delaval or other style claw upside-down. Ideal for storage and cleaning in place, this claw hanger includes hangar and U-bolt for installation on stall tubing.

115VAC with drip-proof motor enclosure. 50-60 Hz, .31 amp. May be plumbed directly to the drain. Drain valve assembly mounts directly to the wash vat drain fittings with a no-hub coupling (available separately).

High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Butt weld bevel-seat ferrule for 2" tubing is 23/32" long and B-dimension of 2-3/8" and C-dimension of 1-55/64".

Part number "348-28" on schematic diagram.

External Seal Kit. Includes 1 head O-ring, 2 impeller clips, 1 ceramic ring assembly and 1 carbon seal assembly. This kit is for the LC Thomson Model 5 Milk Pump.

90 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends. Elbow for 2" OD tube features inner radius of 3" and center distance (C) of 3.5".

45 Degree Tube Bend is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends. Bend for 3" OD tube features "B" dimension of 3".

90 Degree Sweep Ell is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on one end and butt weld on the other. Ell for 3" OD tube features "A" dimension of 6-5/16" and "B" dimension of 6-13/16”.

Short round wash and milk shut-off plug for 2-1/2" line.

This CIP Assembly for Surge features Stainless Steel jetter rack and 120116 jetter cups. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation.

Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features a standard clamp on one end and butt weld on the other. Ferrule for 2.5" OD tube is 1/2" long with 2.370" ID.

Plain Recessless Ferrule for standard clamp is made of Type 304 Stainless Steel with #4 Dairy Finish. 1-1/2" long for 4" OD tube.