Milk Line Washing Components Farm Supplies For Sale In Austin

Diverter Plug for 2" Glass Tee.

May be plumbed directly to the drain. 50-60 Hz, .31 amp. Drain valve assembly mounts directly to the wash vat drain fittings with a no-hub coupling (available separately). 115VAC with drip-proof motor enclosure.

RFE Silicone Grease f / Peristaltic Pump Tubing. Silicone Grease (Required when replacing Peristaltic Pump Tubes)

Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head. Replaces Milk-Rite 7100.

CIP Thermometer is used to make sure the CIP wash solution is at the required 160F degrees at the start of the wash cycle. Thermometer has a recalibration feature and includes a plastic carrying case.

Short round wash and milk shut-off plug for 3a" line.

This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120115 Jetter Cups for DeLaval and IBA. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts.

Three-Pump Dispenser features three motor-driven peristaltic pumps each with 300 oz. It may be combined with the 8950 Timer Control Module for more functionality. Capacity, switch setting to program pump run time, hot and cold water valves, cycle timer...

Coburn"s S.S. Distributor Tee is smooth and clean throughout for efficient water flow. Tubes are aligned for ease and convenience of hose handling.

Improved Sentinel Air Injector activates at a minimum of 5" of vacuum, has a capacity of 200 cubic feet of air per minute on 15" of vacuum, and can be easily adjusted. Wall or direct-mounted, air injector operates on 120 volts.

Long round wash and milk shut-off plug for 2" line.

High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and featuresstandard clamp fitting on both ends. Reducer from 4" OD to 3" OD tube is 5-1/8" long.

45 Degree Tube Bend is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends. Bend for 2.5" OD tube features "B" dimension of 3".

Butt weld bevel-seat ferrule for 2-1/2" tubing is 27/32" long and B-dimension of 2-29/32" and C-dimension of 2-23/64".

Each pump has a multi-time module to program on/off, run times and delay times from 1 second to 45 minutes. L5000 Plus Panel features stainless steel cabinet with new sloping design, snap-in pump heads, internal trigger module, and 20 oz/600ml per minute...

90 Degree tube bend for 4" tube OD features "A" dimension of 8-5/16". Type 304 Stainless Steel.

180 Degree clamp-end U-bend for 2.5" tube OD features "A" dimension of 7-1/2". Type 304 Stainless Steel.

Plain Recessless Ferrule for standard clamp is made of Type 304 Stainless Steel with #4 Dairy Finish. 1-1/2" long for 4" OD tube.

This smooth, white Tee is made out of food-grade plastic.

Rubber tri-clamp gasket for 3" OD tubing.

Solid End Cap for Tri-Clover line is made of Type 304 Stainless Steel with #4 Dairy Finish. End cap for 4" OD tube has 4.68" OD.

Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features a standard clamp on one end and butt weld on the other. Ferrule for 3" OD tube is 1/2" long with 2.834" ID.

Butt-Weld-end Special Y for 3" tube OD features "A" dimension of 5" and "B" dimension of 10". Type 304 Stainless Steel.

90 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends. Elbow for 1" OD tube features inner radius of 1.5" and center distance (C) of 2".

Butt weld bevel-seat ferrule for 1-1/2" tubing is 23/32" long and B-dimension of 1-27/32" and C-dimension of 1-23/64".

This high-quality butterfly valve for 2" tube is made of type 316 Stainless Steel for clamp connection. Not recommended for applications where pressure exceeds 150 psi.