Livestock Waterers Farm Supplies For Sale In Santa Ana

Rubber shut-off pad and ABS plastic and stainless steel internal parts ensure long life. Unlike common ball float valves, the Hudson Valve does not constrict the flow prior to positive shut-off.

Unique covered design aids in eliminating debris from contaminating the water supply Holds 2 gallons Bottom drain for easy cleaning Can be attached to timber rails, wall, pipe rails or steel gate Includes 4 self taping screws & 4 cable ties for installation...

The SPI Insulated Earth Tube conserves the earth ground source heat as it rises up the vertical shaft to help protect the water line from freeze ups. It has an excellent insulating property of R15 and amazing structural strength.

It moves the upper to and is also held by a thumbscrew to the float arm. The lower arm is orange and is located in the bottom bracket of the top base and is held by a lock pin.

SPI 90 degree elbow for all models.

Polyethylene Cage Cup has molded-in hooks to clip onto the side of any type of wire animal cage. Useful for feeding or watering rabbits, poultry or any type of small animal. Capacity is one-half pint (1 cup).

The Trough-O-Matic float valve features a longer, deeper float which gives more leverage. Water pressure and has a capacity of 375 gallons per hour. The rust-proof plastic case comes with an adapter to fit a 3/4" male or 1/2" female pipe.

This Dare anti-siphon farm tank float valve with weather-resistant plastic housing has a 300 gallon per hour capacity and a tough blow-molded plastic float. Connects to 3/4" garden hose or adaptable for pipe.

Float and arm are molded of high-impact styrene and the valve body is made of Delrin. Overall length is about 6". Float Valve for poultry waterers is made of plastic to cut down on corrosion and scale build-up.

Fully submerged valve is almost indestructible to livestock and models come in standard tail length and long tail length. XtraFlo is UV stabilized and corrosion resistant. XtraFlo compact diaphragm valve has full-flow, high volume fill.

It is held by a float screw and connects on to the bottom of the float arm. Plastic piece that sits on top of the float.

SPI 351/352 New Generation Gasket.

Blue octagon plunger that fits inside the Mira Fount cattle waterer valve.

Float Arm for the Mira Fount M3330 waterer.

Custom made to use in all Rubbermaid stock tanks with 1500 Watts of power. Thermostatically controlled to only run when necessary. Unit is unnoticed by livestock - no cord in water.

The Trough-O-Matic float valve features a longer, deeper float which gives more leverage. Anti-siphon feature makes this valve approved for Grade A dairy farms. The case is made out of a rust-proof plastic and is fitted for a male 3/4" threaded hose.

Use this valve assembly with the J303 with without heat.

Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm. Blue plastic valve assembly fits a 3/4" FPT with a .45" orfice inlet, includes arm that will fit any length, 2 thumbscrews & plastic float.

Robert's Brass thumbscrew that connects the short arm and long arm.

Available in light gray. Heating cost is minimal-less than $10.00 per heating season. No freezing occurred at this temperature-even after 7 days! Double wall, single piece poly construction -- ALL SMOOTH! Internal 3/4" (1.9 cm) AND external 2" (5.1 cm)...

Jug Thermostat fits Models 101, 202, 303 & 404 with heat.

O'Ring only replacement for Frost Pro Accessory.

Fully submerged valve is almost indestructible to livestock and models come in standard tail length and long tail length. XtraFlo is UV stabilized and corrosion resistant. XtraFlo compact diaphragm valve has full-flow, high volume fill.

VP2 Valve Upgrade Kit for 1/8" Orifice Valve

Fully submerged valve is almost indestructible to livestock and models come in standard tail length and long tail length. XtraFlo is UV stabilized and corrosion resistant. XtraFlo compact diaphragm valve has full-flow, high volume fill.

B79P Plastic Float with Arm for WFD85 and MFD85 field drinkers. B79P includes:Ref. 14, 15, 16 in parts list.

Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm. Blue plastic valve assembly fits a 3/4" FPT with a .25" orfice inlet, includes arm that will fit any length, 2 thumbscrews & plastic float.