Livestock Waterers Farm Supplies For Sale In Murrieta

SPI's energy free waterer is built using 100% polyethylene construction creating a strong corrosion free product to provide many years of trouble free operation. The low profile design and fully hinged door provides animals better access to the water.

Specify model 354, 352 or 351 energy free waterer. SPI foamed door only.

Plastic screw that holds the float arm to the valve's lower arm at the top and the float connect at the bottom.

SPI 4x4 - 3/8" x 1" x 22' gasket only.

Must be used with part #400267 Plunger Only. This black seat fits inside the plunger and shuts off the water through the orfice.

Float Valve for poultry waterers is made of plastic to cut down on corrosion and scale build-up. Overall length is about 6". Inlet pipe thread is 1/2" male and 1/4" female. Float and arm are molded of high-impact styrene and the valve body is made of...

15" OD, corrugated plastic tubing. It will take abuse! Corrugated design provides rigidity without bulk when back filled with earth. Unaffected by ground movement due to freezing & thawing.

20 Gallon, 36" x 35" x 25" - 1060# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

Robert's Brass 3/4" plunger only for replacement in existing 3/4" valve.

Robert's shut off only arm attached to the bottom of the Robert's Brass Valve.

No inside working parts included. The orange male fitting end of the Franklin Valve.

1000 watt x 240 volt heating element only. Arkfeld waterer element replacement.

Robert's Brass cotter key that connects the long arm to the valve body.

This part number is for the arm only & is usually used on the Polar Max waterers. Pride of the Farm Plastic 3 5/8" Float arm is connected to the Power Link by a thumbscrew & then screws directly into the Poly float.

Guaranteed for 1 year & SAFE IN PLASTIC. Thermostatically controlled to only run when necessary. Easy to install & installs in only minutes. Unit is unnoticed by livestock - no cord in water.

Drinking height is 15" Door Opening is 9 1/2" x 9 1/2" and trough holds 17 gallons of water. This waterer has a MAX usage of 120 Beef, 50 Dairy or 135 Sheep. An Earth Tube is suggested with installation.

Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm. Blue plastic valve assembly fits a 3/4" FPT with a .45" orfice inlet, includes arm that will fit any length, 2 thumbscrews & plastic float.

This part number is for the arm only & is usually used on hog troughs. Pride of the Farm Plastic 2 1/2" Float arm is connected to the Power Link by a thumbscrew & then screws directly into the Poly float.

Blue octagon plunger that fits inside the Mira Fount cattle waterer valve.

All edges have been rounded for safety & strength. 3 year warranty. If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill the hole.

Our VT100 valve delivers about 2 1/2 gallons (9.5 liters) per minute. Double wall, single piece poly construction--ALL SMOOTH! Foam filled insulation--R value of 7.5 per inch which offers lots of freeze protection.

Black rubber seat to fit inside the Mira Fount Blue Plunger in a Mira Fount cattle waterer valve.

#6 on breakdown. Pride of the Farm Rubber Diaphragm that fits between the orifice & the plunger on a VP124 valve.

Upright Water Caddy Stand (24694) will work with this water caddy. This tank fits conveniently into the "dead space" in the corner of the walk-in tack room. White 14 1/2" x 14 1/2" x 56" tall.

This bolt package is for Models 101, 202 & 404 with or without heat.