Livestock Waterers Farm Supplies For Sale In Lakewood

SPI 4x4 - 3/8" x 1" x 22' gasket only.

Robert's shut off only arm attached to the bottom of the Robert's Brass Valve.

Rubber shut-off pad and ABS plastic and stainless steel internal parts ensure long life. Each valve comes with installation instructions, warranty information and parts list. Fluid level forces the float to rise and close the diaphragm chamber, which...

This piece is held by two thumbscrews not included in this part. 3" orange arm that fits between the lower arm and the float connect.

Constructed of Cast Aluminum for ultimate efficiency & safety. The most durable floating tank de-icer available with 1250 Watts. Ideal for use in Ponds 50 to 600 gallons. Thermostatically controlled to only run when needed.

It has O'ring on one side & a Diaphragm on the other (not included). #7 on breakdown. Pride of the Farm 1/4" Orifice on a VP124 Valve.

Repair kit includes 1 each screen, retainer ring, diaphragm, shut-off pad and float.

Connects valve to 301 round float. A brass rod float arm 1/4" x 6" with threads on each end.

Robert's Brass cotter key that connects the long arm to the valve body.

Robert's Brass 1/2" orfice Valve complete with sand plunger and arms.

VP2 Valve Upgrade Kit for 1/8" Orifice Valve

Suggested where sugar sand is a problem in the water supply. Robert's Brass 3/4" sand plunger only for replacement in existing 3/4" valve.

45 Gallon, 48" x 35" x 25" - 1345# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

Mostly used on Franklin hog waterers. Orange plastic valve assembly fits a 3/4" FPT with a 1/2" orfice inlet.

The VS20LPC has an insulated valve cavity and one piece hatch for no air loss. This two hole, 5.2 gallon waterers uses a 250 or 500 watt submersible heater and can easily ship UPS.

SPI 90 degree elbow for all models.

Same desription as the J202 EXCEPT THIS UNIT HAS NO HEAT!

Connects valve to 301 round float. A brass rod float arm 1/4" x 8" with threads on each end.

Water enters the MiraFount at 45 to 48 degrees. Each model comes with anchors for mounting to concrete pad, pipe insulation, and a section of 3/4" PVC pipe. Whenever an animal drinks, it removes a quantity of water which is immediately replaced by ground...

Connects valve to 301 round float. A brass rod float arm 1/4" x 10" with threads on each end.

A drain plug for the Arkfeld waterers - 1 1/2" in size - Black rubber.

It has an excellent insulating property of R15 and amazing structural strength. Highly recommended for ALL cold climate installations. They can also be easily stacked for deeper installations.

3-year warranty. No stand available for this water caddy. 2 water valves, one at the bottom and the other 14" from the floor. 2 mounting straps. 10 1/2" side panels x 11 1/4" front panel x 71" tall.

Connects valve to 301 round float A brass rod float arm 1/4" x 1 1/2" with threads on each end.

Valve is rated at 2 gallons/8 liters per minute at 50 PSI. Bowl has two 3/8” holes for mounting and ½” top water inlet. Mini-Size Water Bowl for goats and sheep has nose paddle water release and comes in high-impact polypropylene.

This part number is for the arm only & is usually used on the Polar Max waterers. #12-3 on the breakdown. Pride of the Farm Plastic 3 5/8" Float arm is connected to the Power Link by a thumbscrew & then screws directly into the Poly float.