Livestock Waterers Farm Supplies For Sale In Concord

XtraFlo is UV stabilized and corrosion resistant. XtraFlo compact diaphragm valve has full-flow, high volume fill. The top entry model provides an air gap, preventing back-flow. Fully submerged valve is almost indestructible to livestock and models come...

Hollow black plug used in all Franklin galvanized waterers.

Includes seat and float. Repair Kit for Water Control Valves model 825H , 825P , 830H , 830P , 825ASH and 825ASP .

Plastic screw that holds the float arm to the valve's lower arm at the top and the float connect at the bottom.

XtraFlo is UV stabilized and corrosion resistant. XtraFlo compact diaphragm valve has full-flow, high volume fill. The top entry model provides an air gap, preventing back-flow. Fully submerged valve is almost indestructible to livestock and models come...

This Complete Valve is used on the J303 or J303EF Corner Mount Horse Stall Waterer.

Each valve comes with installation instructions, warranty information and parts list. Fluid level forces the float to rise and close the diaphragm chamber, which expands to stop incoming flow.

SPI 4x4 - 3/8" x 1" x 22' gasket only.

XtraFlo is UV stabilized and corrosion resistant. XtraFlo compact diaphragm valve has full-flow, high volume fill. The top entry model provides an air gap, preventing back-flow. Fully submerged valve is almost indestructible to livestock and models come...

It is held by a float screw and connects on to the bottom of the float arm. Plastic piece that sits on top of the float.

It also features a molded bolt foot and rounded corners for livestock safety. No more rust or corrosion! These electric waterers are built of a polyethylene construction creating a strong corrosion free product to provide many years of trouble free operaton.

#6 on breakdown. Pride of the Farm Rubber Diaphragm that fits between the orifice & the plunger on a VP124 valve.

Turns on at 35 degrees & turns off at 45 degrees. Five controlled temperatures (one just right for you) & no installation required. Saves money by using power only when temperatures require.

Dimensions: 41" x 20" x 23". Maximum 24-hour electrical use is 1.56 kwh. Features: *Open bowl design *Draw Tube for natural drinking action *External Drain Plug for easy cleaning *Sledge hammer tough, rotationally molded plastic construction *Inspection...

Replacement Plastic Valve & Float f/ WFD85 and MFD85 field drinkers.

Blue 10 3/4" replacement ball for the Mira Fount 3354S, M3370S, M3390, M3390E cattle waterers & 3360-10 hog waterer.

Optional wing bolts are available for Grade A inspections. No heat well needed; use an 8-12" tile; can be fitted on most existing pads. Notched flanges for easy anchoring. Livestock can drink out of both flaps at the same time, not always so with a ball...

Connects valve to 301 round float. A brass rod float arm 1/4" x 5" with threads on each end.

DO NOT SUMBERGE THE REPLACEMENT SENSOR, it is only designed to sense the temperature of the air. It is not adjustable for temperature. It will turn on the heating element at 45 degrees Fahrenheit and off at 60 degrees to provide reliable freeze protection...

No stand available for this water caddy. 14” side panels x 14.5” front panel x 72” tall. Constructed with FDA-approved materials, with a vent in the fill cap on top of the caddy.

The Robert's 3/4" brass valve housing only.

Same desription as the J202 EXCEPT THIS UNIT HAS NO HEAT!

1 per model EXCEPT 404 models need 2 kits. Weather seal Kit for Jug 101, 202 & 404 with or without heat.

Robert's 3/4" rubber plunger seat only.

Inside repair kit for Topaz & Megaflow Valve.

Optional ground mount tube (Model HT10) for hookup to underground service connections and for outdoor installations. Half moon design on back corner for securing up to a 2 inch (5.1 cm) PVC tube for plumbing from above or below.

Must be used with part #400267 Plunger Only. This black seat fits inside the plunger and shuts off the water through the orfice.