Kirby Mfg Inc Used Equipment For Sale In Wisconsin

Near new condition,plenty of arch left,sliding winches,chain tie downs,nail strips,,save some money by buying all three,coil kits,big outer wheel bearings, 23,000 # axles,all steel parts have been sandblasted,rimed and painted.

Summers MFG Super Roller Model # RG8410 21' Hydro Fold 9/16" Drum Wall New 36" Drum

Used Summers 23' Super Coulter Disk w/HYD Leveling; 20"

Summers Mfg Supercoulter Plus 12' with Rolling Choppers Used very little

2019 MAC 30 FT ALUMINUM FRAMED END DUMP 2 PRIMARY AXLES WITH FRONT LIFT AXLE (54 INCH SPACING), 1/4 INCH FULL FLOOR, 10 INCH CROSSMEMBER SPACING, OUTSETSMOOTH SIDE PANEL, AIR CAB CONTROL GATE OPERATION, 12 INCH COAL DOOR

Steel 1/4 frame, poly liner floor, 68" sides, 16" king pin setting, 80,000# GCWR, flip tailgate w/coal door, roll tarp, round bottom, all 3 axles stay on ground when box is raised, hinged 5th wheel plate, susp dump valve, air latch tailgate, led lights

30' Coulter, Straight Front Blades, Wavy Rear Blades, Coil Tine Harrow, Wing Weights, 12.5L Tandems, Contact Brian for Additional Details!

VERY NICE SHAPE

30 ft with 13 wave front and rear, 2 row danish tine and 2 row coil tine. Weights not included.,

24 foot, straight front blades, wavy rear blades, rear roller chopper, good blades and choppers

Stacker, clean, good paddles

70% rubber, and toll tarp system. This trailer has a SS liner and is in excellent condition, with new brakes, and drums and cams. THIS IS A FRAMELESS END DUMP TRAILER Combination swing/lift/coal shoot gate.

Roll hose from the front or the back. Add air or hydraulic brakes for $58,500. Open spool design with 180 degrees of rotation. Dual axles with high flotation tires. BEI HCT-10 hose cart.

Good condition, good knives, stack mover avable

A hydraulic motor is connected to a gearbox that rotates the horizontal discharge auger. The Charger II-FB will unload up to 3,500 pounds per minute. This versatile system can rotate 270 degrees, allowing you to unload to the left, right or the rear of...

Another hydraulic cylinder raises or lowers the discharge tube to the desired height. The Charger II-SF Side-Discharge Tender is efficient, unloading up to 4,000 pounds per minute.

A hydraulic motor is connected to a gearbox that rotates the horizontal discharge auger. The Charger II-FB will unload up to 3,500 pounds per minute. This versatile system can rotate 270 degrees, allowing you to unload to the left, right or the rear of...

A hydraulic motor is connected to a gearbox that rotates the horizontal discharge auger. The Charger II-FB will unload up to 3,500 pounds per minute. This versatile system can rotate 270 degrees, allowing you to unload to the left, right or the rear of...

30 Ft, Rolling Basket, #173250, 30 Ft Rolling Basket

8 1/2 Ft, Front Mounted Flail Mower, Used Very Little, Front 3 Point and PTO are Required, #166357,

Heavy duty undercarriage with truck tires. 40' Lagoon Prop agitator. Heavy Duty 10" square tube frame. Clean, well maintained and heavy built unit! 1000 rpm shaft.

30 Ft, Rolling Choppers, Good Blades Front & Rear, Weight Kit, #175038 30 Ft Rolling Choppers Good Blades Front & Rear Weight Kit

Used Weatherall 2700 Row Crop Cultivator; 6 row; 7x7 tool bar; 3pt mount; 4" front twin press wheels; single spring reset, Color: W, horsepower: 0

Vermeer BC700XL Chipper; 6" capacity, 25 hp Kohler gas engine, "smartfeed" feed control system, $13,250.00

Vermeer SC362 Stump Grinder; 35 hp gas engine, dual drive tires, Autosweep, two speed drive, Yellow jacket cutter system, $16,950.00

OMC ROUND BALER

-Low discharge points to minimize slurry contact with the air. -Equiped as either a pull type or three point (with or without a swing pipe mounted on the toolbar). A few features of our top application toolbar: -4" Discharge hoses to allow minimal hose...