Farm Equipment Swine Equipment For Sale In Tempe

This is a complete Lower Boot that will accomodate a Single M108 auger exiting the boot at a 30� angle. Does not include plastic upper transition boot. Chore-Time Model 108 Single 30� Lower Boot Assembly.

This is the top plug on all Chore-Time Gearheads. Chore-Time Replacment Vent Pipe Plug.

Uses CT3249 Pinion Gear. Chore-Time Gearhead Assembly 216 RPM used in Model 75, 90, HMC, 125, 108 & MF systems.

Contains hose, 06654 adapter. Supply Hose, 3/8" x 10' for Models Guardian60/100, Classic 60N, 115, 115N, 40 (NG).

Chore-Time Diaphragm Assembly for CT46051 Switch Assembly

Easy-to-read feed level adjustment allows feeding individual amounts from 3/4 to 10 pounds (0.3 to 4.5 kg). Translucent feeder provides quick visual check of its contents. Chore-Time Model 55 Clear Drop Feeder Assembly.

Igniter only, no bracket, for HSI and Guardian heaters, (509201)

Attaches to the bottom of the control unit box and funnels feed into a round discharge. Chore-Time Model 75/90 Control Unit Funnel.

Chore-Time Nylon Pulley Assembly

Use with Model 90/ HMC/108 Outlets and CT6381 Drop Tube. Chore-Time Model 90/HMC/108 Drop Tube Pin.

This is the bearing assembly used on CT35343, CT35344 & CT35345 Anchor & Bearing Assemblies. Chore-Time Model 90/HMC Bearing Cap Assembly.

This Weldment will accept the M90 Tube. Chore-Time Model 90 Model Parts Package. Include the Tube Anchor Plate Weldment, Clamp and Hardware to bolt to the Control Unit.

Located at the control unit end of the Flex Auger syystem. Chore-Time Model 55 Driver Tube. Driver tube is the piece the Flex Auger slides over and attached to.

Valve, Gas control, (LP Gas), 11" W.C., use in AW215CH, AW230EH, FH; All Guardian Models

Maximum moisture content = 18%. Delivery Rate = 100 lb./min. Used to convey mash, crumbles or small pellet feeds. Maximum particle size = 3/16" dia. I.D. = 1.75" O.D. = 2.71" With standard 348 RPM power unit.

Chore-Time Model 108 Plastic Drop Tube (5" x 12')

Regulator, Single Stage (LP), Classic 60/346, Classic 115/ 377

This is a complete Lower Boot that will accomodate Two M90 augers exiting the boot horizontal to the ground. Does not include plastic upper transition boot. Chore-Time Model 90 Twin Straight-Out Lower Boot Assembly.

Chore-Time Micro switch for Hopper Level Control.

Replacement parts: Motor = CT5051, Pinion Gear = CT5046, Gearhead = CT3261-7 Chore-Time Model 75/90/HMC/108 3/4HP, 348RPM, 230V, 60HZ, 1PH Power Unit. Used on M75 Flex Auger sysems from 90' - 150' in length, M90 & HMC Flex Auger sysems from 40' - 90'...

They will cause the heat mat to overheat. Perfect for outdoor pens, kennels, garages, dog houses, whelping areas, veterinary clinics, and barns. Made of durable, easy to clean polyethylene, Kane mats provide a safe and consistent heating surface.

Chore-Time Model 90/HMC Tube Clamp (PVC or Steel)

Big enough for sows, yet small enough for baby pigs. Stainless-Steel trip plate & housing. Trojan's Cast Iron Cup with powder coat finish "Super Stong". All Models use the same tried & proven non-siphoning trouble free 393 valve.

Each Tube is 10' long. Chore-Time Model 55 PVC Tubing.

Ideal for farrowing stalls, creep areas and nurseries. The wrench flats make installation an easy task for this one piece body that fits standard 1/2" connections. Even the smallest pgis like the easy bite trigger and tapered end on the Spiglet.

Chore-Time Replacment Oil Seal (Pinion Side) for Gearheads CT32615 & CT32617

Used under a drop to "Y" or split the feed from one drop tube in to 2 drop tubes. Chore-Time Model 55/75/MF "Y" Outlet.