Farm Equipment Swine Equipment For Sale In Santa Ana

LP Gas Orfice, Burner, for Classic 60/ 346 heaters

I.D. = 1.44" O.D. = 2.38" Maximum particle size = 5/32" dia. Used to convey mash, crumbles or small pellet feeds. Chore-Time Model 75/HMC Flex Auger. Maximum moisture content = 18%.

This is the top plug on all Chore-Time Gearheads. Chore-Time Replacment Vent Pipe Plug.

This is the red plastic tube anchor that bolts to the control unit and accepts the pvc pipe. Chore-Time Model 55 Tube Anchor.

Each Tube is 10' long. Chore-Time Model 75 PVC Tubing.

Used on Model 75/90/HMC/108 anchor & bearing assemblies. Chore-Time 5/8" Shaft Collar.

NG Orfice, Burner, for Classic 170/410

Also used on Model 108 Anchor & Bearing Assembly Chore-Time Flex Auger Clamp for Model 75/90/HMC Driver Weldment at Control Unit.

Chore-Time Model 75/90/HMC 1/2HP, 348RPM, 230V, 60HZ, 1PH Power Unit. Used on M75 Flex Auger sysems from 20' - 80' in length, M90 & HMC Flex Auger sysems from 20' - 30' in length. Replacement parts: Motor = CT5050, Pinion Gear = CT5046, Gearhead = CT32617

Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc. This is the lower boot body only. For a complete lower boot use part number CT9313

Regulator, Single Stage (LP), Classic 60/346, Classic 115/ 377

Chore-Time Model 75 Tube Clamp (Steel)

Each kit includes 25 "S" Hooks, 12 Screw Hooks and 25' of double loop chain. Used to suspend the Flex Auger from the ceiling. Quantity needed is determined by the size and length of the auger system.

Chore-Time Micro Switch for CT46051 Switch Assembly. Used on CT46800 Control units. (Old number CT7114)

Use with Model 90/ HMC/108 Outlets and CT6381 Drop Tube. Chore-Time Model 90/HMC/108 Drop Tube Pin.

New improved design, made of molded one-piece plastic, make the new Blue Finisher waterswing better than the stainless waterswing, at a galvanized price. It is non-corrosive, self-cleaning with no internal areas for sludge deposits, and threads molded...

I.D. = 1.75" O.D. = 2.71" Maximum particle size = 3/16" dia. Used to convey mash, crumbles or small pellet feeds. Chore-Time Model 90 Flex Auger. Maximum moisture content = 18%. Delivery Rate = 100 lb./min.

Used at the end of a Drop Feeding system to control the operation of the power unit. Chore-Time Model 55 Mechanical Drop Feeder Control Unit.

Package contains hose, 06654 adapter. Supply Hose, 3/8" x 10' for Models Guardian60/100 HSI.

Attaches to the bottom of the control unit box and funnels feed into a round discharge. Chore-Time Model 75/90 Control Unit Funnel.

Chore-Time Diaphragm Assembly for CT46051 Switch Assembly

Chore-Time Model 75 Tube Connector w/Clamps

Assembly includes CT7706 Driver Weldment, CT7703 Aguer Clamp and Cap Screws. Chore-Time Model 90 Driver Weldment Assembly.

Kane�s polyethylene heat mats installed with�thermostat controls are simply the most energy efficient heat mats in the world.� Kane thermostats reduce power consumption by an additional 50% of the rated watts per crate listings.� Designed for...

Pilot Light Orfice, (NG), for Classic 60/348, Classic 115/379, Classic 170/410

Chore-Time Model 55 Direct Drive Control Unit, 1 Phase

Chore-Time Model 55 Model Parts Package. Include the Tube Anchor Plate Weldment, Clamp and Hardware to bolt to the Control Unit. This Weldment will accept the M55 Tube.