Farm Equipment Swine Equipment For Sale In Providence

Chore-Time Model 75 Mechanical Drop Feeder Control Unit. Used at the end of a Drop Feeding system to control the operation of the power unit.

Chore-Time Replacment Oil Seal (Pinion Side) for Gearheads CT32615 & CT32617

Chore-Time Model 90 Anchor & Bearing Assembly. Short anchor tube on this assembly allows for less restriction and more flow into the auger.

Chore-Time DPST Toggle Switch-4 Prong. Used on Flex Auger models 55/75/90/HMC Older Style Metal Control Unit (Part Numbers 6500-). This is the toggle switch that is located on the control unit (220v, single phase).

Chore-Time Model 75 Tube Clamp (Steel)

Pilot Light shield for Classic 115/377/379

Flame sensor with 40" lead for models AB200, AW230, AW325

Maximum particle size = 5/32" dia. Maximum moisture content = 18%. Chore-Time Model 75/HMC Flex Auger. Delivery Rate = 50 lb./min. With standard 348 RPM power unit. I.D. = 1.44" O.D. = 2.38"

Enable multiple feedings per sow per day by automating drop feeders with one of the proven CHORE-TIME � Winch systems. Chore-Time Model 55 Clear Drop Feeder Assembly. Easy-to-read feed level adjustment allows feeding individual amounts from 3/4 to 10...

Screen filter keeps foreign matter out of valve. Easy to install! Simply drill a 7/8" hole in your barrel, bucket, pipe or stock tank. Sealing ring resists buckling or slipping during installation, and provides a complete 360° seal.

Chore-Time Model 75/90/HMC 1/2HP, 348RPM, 230V, 60HZ, 1PH Power Unit. Replacement parts: Motor = CT5050, Pinion Gear = CT5046, Gearhead = CT32617 Used on M75 Flex Auger sysems from 20' - 80' in length, M90 & HMC Flex Auger sysems from 20' - 30' in length.

Control, Hot Surface Ignition

Chore-Time Model 55 1/3 HP, 348 RPM, 60HZ-1PH 230V Power Unit. Replacement parts: Motor = CT4229, Pinion Gear = CT5046, Gearhead = CT32615 Used on Flex Auger sysems from 20' - 150' in length.

Chore-Time Model 108 45D PVC Elbow

Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly. Chore-Time Model 75 Single 30� Lower Boot Assembly. This is a complete Lower Boot that will accomodate a Single M75 auger exiting the boot at a 30� angle.

Chore-Time Model 75/HMC Driver Weldment Only. Auger slips over tube and uses CT7703 Auger Clamp/

Chore-Time Nylon Pulley Assembly

Just plug your heat mat into the bottom of the control and create a warm, dry environment for your small animals. Dial-A-Temp plugs right into your outlet to provide a quick and easy way to regulate temperature.

Delivery Rate = 220 lb./min. Used to convey high moisture corn, large pellets, shelled corn or ground feed. With standard 348 RPM power unit. Maximum moisture content = 27%. Maximum particle size = 3/16" dia.

Chore-Time Replacment Oil Seal (Output Shaft) for All Chore-Time Gearheads

Chore-Time Model 55/MF Tube Clamp

Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly. Chore-Time Model HMC Single Lower Boot Assembly. This is a complete Lower Boot that will accommodate a Single HMC auger exiting the boot at a 30� angle.

Prevent water lines from freezing. Useful as a heat supplement on supply lines under livestock waterers. After installation on your pipe, simply connect to any 110v electrical supply line or thermostat.

Chore-Time Model 75 Anchor & Bearing Assembly (CT #37346). Long anchor tube on this assembly allows for more controlled flow into the auger.

Chore-Time Twin Manual Slide Assembly. Telescoping Drive Tube/Handle also available CT47638 Rack and Pinion style Slide Shut-Off assembly for Twin (2) Auger Boots.

Chore-Time Model 55/75/90/HMC Drop Tube Pin. Use with Model 55/75/90 Outlets and CT1932 Drop Tube.

Honeywell Gas Valve, NG Gas, for "K" series or later Pilot Light "Classic" heaters.