Farm Equipment Swine Equipment For Sale In New Mexico

Include the Tube Anchor Plate Weldment, Clamp and Hardware to bolt to the Control Unit. This Weldment will accept the M55 Tube. Chore-Time Model 55 Model Parts Package.

Our new mat is 30% more efficient then fiberglass mats and 80% more efficient than heat lamps. Kane's unique design maintains the optimal temperature for your farrowing environment to reduce stress, improve digestion, and promote rapid growth.� NRTL,...

Chore-Time Model 75 Tube Connector w/Clamps

Chore-Time Clean-Out Cover Assembly. This is the auger access door assembly that mounts in the side of a Chore-Time lower boot.

Chore-Time Model 75 Bearing Cap Assembly. This is the bearing assembly used on CT35346 & CT35347 Anchor & Bearing Assemblies manufactured since May 1996.

Maximum particle size = 3/16" dia. Used to convey mash, crumbles or small pellets. Delivery Rate = 15 lb./min. Chore-Time Multiflo Flex Auger. Maximum moisture content = 18%. I.D. = .89" O.D. = 1.52"

Chore-Time Replacment Oil Seal (Pinion Side) for Gearheads CT32611, CT32612, CT32616 & CT32618

Chore-Time Model 90/HMC PVC Tubing. Each tube is 10' long.

It is non-corrosive, self-cleaning with no internal areas for sludge deposits, and threads molded right in for consistency and better sealing. Our Patented Exclusive "Play Guard" will reduce water waste during the act of drinking.

This is a complete Lower Boot that will accomodate a Single M108 auger exiting the boot at a 30� angle. Does not include plastic upper transition boot. Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly.

Fan Wheel, 8" Diameter x 4-7/8, for Classic 115/377/379

Chore-Time Model HMC Anchor & Bearing Assembly. Long anchor tube on this assembly allows for more controlled flow into the auger.

Used on Flex Auger sysems from 20' - 150' in length. Replacement parts: Motor = CT4229, Pinion Gear = CT5046, Gearhead = CT32615 Chore-Time Model 55 1/3 HP, 348 RPM, 60HZ-1PH 230V Power Unit.

Chore-Time Model 75 Direct Drive Control Unit, 1Phase

LP Gas Orfice, Burner, for Classic 60/ 346 heaters

Pilot Assembly with LP Orfice for Classic heaters

The Sensor Plus Drop Tube Switch has a built in safety timer that allows the operator to set a Maximum Run Time for the auger to ensure that it will not continue to operate if the feed bin runs out of feed or if a drop tube is knocked out of a feeder.

Mount this unit under livestock waterers. An adjustable automatic thermostat permits you to control the temperature for whatever the condition. It runs on LP or convert to natural gas, developing 4050 BTU per hour.

LP Orfice, Burner, for Classic 170/408

Delivery Rate = 50 lb./min. With standard 348 RPM power unit. Used to convey mash, crumbles or small pellet feeds. Maximum particle size = 5/32" dia. Maximum moisture content = 18%.

Chore-Time Replacement 1/4 NPT Pipe Plug. This is the side plug on all Chore-Time Gearheads.

Chore-Time Replacement Pinion Gear. CT5046R Pinion has 21 teeth and a 1/2" diameter bore.

Designed for use with pigs 50 lbs. Outstanding finisher nipple. It's stainless steel body and trigger won't corrode, the trigger has a built-in playguard and features a slotted filter keeping foreign matter out of the valve.

Chore-Time Model 55 Drop Kit with Clamps. Clamps hold the Drop in place.

Chore-Time Model 90 Drop Kit with Clamps. Clamps hold the Drop in place.

Chore-Time Model 75/HMC Driver Weldment Only. Auger slips over tube and uses CT7703 Auger Clamp/

Used to suspend the M55 Flex Auger from the ceiling. Quantity needed is determined by the length of the M55 auger system. Each kit includes 3 "S" Hooks, 10' of double loop chain. Chore-Time Model 55 Suspension Kit.