Farm Equipment Swine Equipment For Sale In Chicago

Supply Hose, LP Gas, 1/4" X 10', for Classic 60/346, (20543)

Chore-Time Model 90/HMC Plastic Drop Tube (3 3/4" x 12')

Chore-Time Model 108 Tube Insert

Maximum particle size = 3/16" dia. Used to convey high moisture corn, large pellets, shelled corn or ground feed. Delivery Rate = 220 lb./min. Maximum moisture content = 27%. Chore-Time Model 108 Flex Auger.

Chore-Time Multiflo Nylon 90� Elbow with Coupler & Clamps.

They will cause the heat mat to overheat. Provide the optimal climate for your animals with Kane's pet and livestock heat mats. Perfect for outdoor pens, kennels, garages, dog houses, whelping areas, veterinary clinics, and barns.

For use on the following power Units: CT325966, CT325982, and CT3259124 Chore-Time Model 108 1.5HP , 230V, 1-Phase Replacement Motor.

Chore-Time Model 55 Direct Drive Control Unit, 1 Phase

Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc. This is the lower boot body only. For a complete lower boot use part number CT36442 or CT 36589

Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly. This is a complete Lower Boot that will accomodate a Single M75 auger exiting the boot horizontal to the ground.

Auger slips over tube and uses CT7703 Auger Clamp/ Chore-Time Model 75/HMC Driver Weldment Only.

For use on the following power Units: CT325950, CT325951 and CT325977 Chore-Time Model 75/90/HMC 1/2HP, 230V, 1-Phase Replacement Motor.

These double panels are perfect for large alleyways, pens and stand alone tasks such as marking and medicating. Rounded hand grips on the top and side make for easy handling. Light weight and small, its perfect for younger members of your crew and can...

Chore-Time Model 75/90/HMC/108 3/4HP, 348RPM, 230V, 60HZ, 1PH Power Unit. Used on M75 Flex Auger sysems from 90' - 150' in length, M90 & HMC Flex Auger sysems from 40' - 90' in length and M108 Flex Auger Systems from 20' - 50' in length.

Uses CT6104 Pinion Gear with 1/2 HP and 3/4 HP motors and CT5046 with 1 HP motors. Chore-Time Gearhead Assembly 348 RPM used in Model 75, 90, HMC, 125, & 108 systems.

This is the auger access door assembly that mounts in the side of a Chore-Time lower boot. Chore-Time Clean-Out Cover Assembly.

This is the side plug on all Chore-Time Gearheads. Chore-Time Replacement 1/4 NPT Pipe Plug.

Made in the near by state of Missouri, here is a hog feeder for your 4H project or small producers raising a few head of livestock. This feeder is easy to fill, made of 20 ga. G90 Galvanized steel, has a flapper rain cover, 2 feed holes & holds approximately...

Chore-Time Model HMC Model Parts Package. Include the Tube Anchor Plate Weldment, Clamp and Hardware to bolt to the Control Unit. This Weldment will accept the HMC Tube.

Clamps hold the Drop in place. Chore-Time Model 90 Drop Kit with Clamps.

Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly. This is a complete Lower Boot that will accomodate a Single M108 auger exiting the boot horizontal to the ground.

The Sensor plus also includes a built in heater to dissapate moisture around the sensor. The Sensor Plus Drop Tube Switch has a built in safety timer that allows the operator to set a Maximum Run Time for the auger to ensure that it will not continue...

Short anchor tube on this assembly allows for less restriction and more flow into the auger. Chore-Time Model 90 Anchor & Bearing Assembly.

Stainless steel bracket, bolts, nuts, washers & 45 degree elbow. Our Model 2000 Wrench Curve Nipple is standard & it's 45 degree angle keeps the pigs standing while drinking. Our Nip-L-Cup allows the pigs to drink from the nipple or from the cup.

Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly. This is a complete Lower Boot that will accommodate a Single HMC auger exiting the boot at a 30� angle.

Long anchor tube on this assembly allows for more controlled flow into the auger. Chore-Time Model 55 Anchor & Bearing Assembly.

Chore-Time Model 90/HMC 45� PVC Elbow