Farm Equipment Swine Equipment For Sale In Cape Coral

Motor, Totally Enclosed, Ball Bearing, 1/8 HP, Guardian 100, AW075

Chore-Time Model 90/HMC Bearing Cap Assembly. This is the bearing assembly used on CT35343, CT35344 & CT35345 Anchor & Bearing Assemblies.

Pilot Assembly with LP Orfice for Classic heaters

Kane�s polyethylene heat mats installed with�thermostat controls are simply the most energy efficient heat mats in the world.� Kane thermostats reduce power consumption by an additional 50% of the rated watts per crate listings.� Designed for...

This kit made to mount the Trojan water swing includes 6 feet of chain, 2 S-Hooks, 1 Screw Hook and 2 - A7900 Trojan Model 2000 Wrench Curve Nipples.

An adjustable automatic thermostat permits you to control the temperature for whatever the condition. It runs on LP or convert to natural gas, developing 4050 BTU per hour. Mount this unit under livestock waterers.

Used on M75 Flex Auger sysems from 160' - 200' in length, M90 & HMC Flex Auger sysems from 100' - 50' in length and M108 Flex Auger Systems from 60' - 100' in length. Replacement parts: Motor = CT6857, Pinion Gear = CT6104, Gearhead = CT32617

For a complete lower boot use part number CT9313 Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc. This is the lower boot body only.

Chore-Time Model 75/HMC Driver Weldment Assembly. Assembly includes CT7704 Driver Weldment, CT7703 Aguer Clamp and Cap Screws.

Chore-Time Model 108 5" Clamp

Chore-Time Replacment Oil Seal (Pinion Side) for Gearheads CT32615 & CT32617

Chore-Time Model 90/HMC Tube Connector w/Clamps

Chore-Time Model 108 Direct Drive Control Unit, 1Phase

This feeder is easy to fill, made of 20 ga. G90 Galvanized steel, has a flapper rain cover, 2 feed holes & holds approximately 150 pounds of feed. Made in the near by state of Missouri, here is a hog feeder for your 4H project or small producers raising...

Chore-Time Model 55/75/MF "Y" Outlet. Used under a drop to "Y" or split the feed from one drop tube in to 2 drop tubes.

Igniter only, no bracket, for HSI and Guardian heaters, (509201)

Chore-Time Model 108 PVC Tubing

Gas Cock Valve, Manual Shut Off with 1/2" pipe nipple. All "Ag " heaters

Chore-Time Model 75/HMC Driver Weldment Assembly. Assembly includes CT7704 Driver Weldment, CT7703 Aguer Clamp and Cap Screws.

Provide the optimal climate for your animals with Kane's pet and livestock heat mats. Made of durable, easy to clean polyethylene, Kane mats provide a safe and consistent heating surface.

Chore-Time Model 55 Tube Clamp. This clamp is to be used to clamp the anchor bearing assembly to the boot.

Just plug your heat mat into the bottom of the control and create a warm, dry environment for your small animals. Perfect for barns, kennels, garages and whelping areas. Dial-A-Temp plugs right into your outlet to provide a quick and easy way to regulate...

Chore-Time Model 55 Direct Drive Control Unit, 1 Phase

Chore-Time Gearhead Assembly 216 RPM used in Model 75, 90, HMC, 125, 108 & MF systems. Uses CT3249 Pinion Gear.

The vinyl coated fiberglass shaft extends completely thru this nw paddle head & into the end of the poker tip making the Rattle Paddle more durable for longer life. The Stix & Paddle shafts are made of a vinyl coated fiberglass to eliminate shattering...

Regulator, Single Stage (LP), Classic 60/346, Classic 115/ 377

Does not include plastic upper transition boot. Comes with boot, anchor and bearing assemblies, slide shut-off kit and side access door assembly. This is a complete Lower Boot that will accomodate Two M90 augers exiting the boot horizontal to the ground.