Farm Equipment Livestock Waterers For Sale In Thousand Oaks

The Tru-Test Apex Xtraflo 1 1/4" valve is a full flow - diaphragm activated, armless, self-cleaning valve mechanism. It's design reduces stock damage & minimises blockage. Minimum inlet pressure 5 PSI, Maximum inlet pressure 150 PSI.

600 watt x 120 volt heating element only Arkfeld waterer element replacement.

This donut shaped 250 Watt De-Icer is designed for multiple uses around the farm. Constructed of Cast Aluminum for ultimate effiency & safety. Guaranteed for 1 year & SAFE IN PLASTIC.

This orange plunger holds the seat (not included) and is pushed by the upper arm towards or away from the orfice.

This Front Float Valve fits Models 101, 202 & 404 with or without heat.

This unit fits the Model 101, 202 & 404 with or without heat.

There are no loose parts. You can expect an entire winter's heating bill of $25.00 or less - and this from a drinker that can water 250 head of beef using only 250 watts. More importantly, the vertical wall of our valve cover has PATENTED ports which...

Robert's 1/2" rubber cup ring that fits on the brass plunger.

It moves the upper arm and is also held by thumbscrew to the float arm. The lower arm is blue and is located in the bottom bracket of the top base and is held by a lock pin.

A Brass short arm to connect the valve and the round float in Arkfeld and SPI waterers.

1000 watt x 120 volt heating element only. Arkfeld waterer element replacement.

Plastic screw that holds the float arm to the valve's lower arm at the top and the float connect at the bottom.

Robert's Brass 3/4" orfice Valve complete with sand plunger and arms.

2-2" drain holes for fast clean out. The WPM80 is an extremely rugged 4 door opening, energy free unit for cattle. Seamless sidewall cannot leak. No pulleys & cable to foul & rust.

This Shut off ball valve is to be used on Models 101, 202 & 404 with or without heat.

Suggested where sugar sand is a problem in the water supply. Robert's Brass 3/4" sand plunger only for replacement in existing 3/4" valve.

It takes a quarter turn with a straight edge screwdriver. Great value & great features don't have to come in a boring, boxy profile. Dependable, non-siphoning Durapride valve. Lower access opening is 6" x 19".

#6 on breakdown. Pride of the Farm Rubber Diaphragm that fits between the orifice & the plunger on a VP124 valve.

40 Watt x 36" Heat Tape used in the Energy Efficient & All Purpose waterers.

Available in Forest Green in stock, other colors available for special order are Ash Grey, Black, Blue, Red & Tan. The one piece construction eliminates cracking & splitting common in plastic-welded, two piece construction tanks.

Saves money by using power only when temperatures require. Operates with any 15 amp 120V electric heater or fan. Turns on at 35 degrees & turns off at 45 degrees. Five controlled temperatures (one just right for you) & no installation required.

These are not included when ordering a base only. There are four base screws that hold the top base to the bottom base.

1000 Watt Immersible element used in the PC2 or PC10 waterer.

The 303 Riser Tube protects the water supply line from the cold by insulating it in urethane foam, and warming it with a low wattage heating element. Water and electric lines run underground below frost line.

The Model HE-CNTRL air sensing thermostat is a replacement for the original "bulb and bellows" thermostat, used to protect from freezing your Hawkeye Steel livestock waterer. Unlike the original concept of the submerged bulb to sense water temperature,...

The tower is foamed filled and the surrounding wall and valve cover are foam filled, Shutoff valve, 3/4" is standard, Through slopes to drain. There also is a 3 inch opening at the bottom of the tower which permits drainage through a tile line to a lagoon,...