Farm Equipment Livestock Waterers For Sale In Grand Prairie

20 Gallon, 36" x 35" x 25" - 1060# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

This unit is insulated with 3 1/2" of polyurethane insulation. With a 40 gallon capacity the waterer has a maximum usage of 200 Beef cows or 90 Dairy cows. SPI's energy free waterer is built using 100% polyethylene construction creating a strong corrosion...

#3 on breakdown. No lock pins or inner parts included. Pride of the Farm VP124 plastic valve body only.

40 Watt x 36" Heat Tape used in the Energy Efficient & All Purpose waterers.

Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm. Blue plastic valve assembly fits a 3/4" FPT with a .45" orfice inlet.

After 3 weeks of use, we have no leaks or overflows. That gives me peace of mind. If the unit does fail, the animals will still have water as it will flow freely. These valves are easy to set up and install and their function is so simplistic it is hard...

68 Gallon, 72" x 35" x 25" - 1910# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

This repair kit fits the Models 101, 202 & 404 with or without heat.

This unit fits the Model 101, 202 & 404 with or without heat.

Robert's 3/4" rubber plunger seat only.

3/4" orfice only for the inside of a Franklin Valve.

#11 on breakdown. Pride of the Farm Plastic Thumb Screw that connects the Power Link & the Float arm (not included).

Pride of the Farm Element for electric waterer units.

This repair kit will fit in all Apex Valves & is made for use in all high pressure or low pressure applications.

15" OD, corrugated plastic tubing. Used to extend the Insulated Earth Tube into warm ground below the frost line & form the Heat Well. Unaffected by ground movement due to freezing & thawing.

Tolerance to water level - you don't have to worry about summer & winter water levels. 2-2" drain holes for fast clean out. Dependable, non siphoning valve - proven & trouble free.

Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm. Blue plastic valve assembly fits a 3/4" FPT with a .45" orfice inlet, includes arm that will fit any length, 2 thumbscrews & plastic float.

It is a split plastic coupler that fits into the corrugation of the Earth Tube. Used for joining multiple Earth Tubes.

600 watt x 240 volt heating element only. Arkfeld waterer element replacement.

Robert's 1/2" rubber cup ring that fits on the brass plunger.

Connects valve to round float. A brass rod float arm 1/4" x 1" with threads on each end.

Stainless steel spring loaded valve cover removes easily. Drinker wells are 14" deep allowing most any animal to drink naturally. Our R-valve of 7.5 per inch holds the heat provided by incoming water.

Suggested where sugar sand is a problem in the water supply. Robert's Brass 3/4" sand plunger only for replacement in existing 3/4" valve.

Available in Aqua Blue color only. 40 1/2" x 28 1/4" x 14 1/4" If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill in the hole.

Robert's Brass cotter key that connects the long arm to the valve body.

THE RACE IS OVER. Simple water level adjustment, easy to clean. Available in light gray. Foam filled-R value of 7.5 per inch. Drinker is very easy to clean-no disassembly for cleaning required.