Applicators Accessories Livestock Supplies For Sale In Tulsa

Used with the Duflex Ear Tag System. Replacement pin used in the DuFlex ProGrip Universal Applicator.

Comes with 3 tips, 2 broad and 1 fine. Deep penetrating formula has a 5 year guarantee when applied properly.

Tagger used to apply Hasco Metal Cattle Tags.

Extra red blunt pin for use in the Allflex Universal Total Tagger or Allflex Global Retract-O-Matic Tagger.

The Y-Tex UltraTagger Plus Applicator was designed with a wide, open throat to prevent pinching the animal's ear. Use the Y-Tex UltraTagger Plus to apply Y-Tex All-American ear tags, Y-Tex RFID tags, and Y-Tex insecticide tags.

2-year warranty. The Dremel 100 Series Ear Tag Engraving Tool is an efficient hand held engraving tool. Lets you mark Ritchey tags permanently in seconds. Single speed rotary tool includes 7 accessories.

Converts 110-volt AC power to 12-volt DC power for AC/DC and DC convertible energizers.

Replacement pin for the yellow Allflex A-Tag Applicator.

Activated when fence pulse is detected Switch to change between DVM and Current Meter modes Retractable voltage probe for reading voltage on energizers and other hard to reach areas Micro-chip technology that enables low voltage operation Detachable ground...

The Insulated End Strainer is a heavy duty, all-in-one, corrosion-resistant assembly to insulate, and tighten up to 4 mm/15 gauge fence wire. 10-year warranty. 12-tooth spool for fine adjustment, robust, high-quality, spring-loaded locking clip.

Connecting gates to a single post.

Use the Y-Tex ear tag removal knife to remove Y-Tex and other ear tags. The Y-Tex ear tag removal knife removes ear tags quickly and safely.

Pig tail clips may be used instead of insulators. Stainless steel clips for use with 3/8" or 1/2" fiberglass posts.

Rated for high-tensile wire. Heavy-duty steel construction. Has a tough insulating grip and strong spring.

Grinding bit used with Dremel tool to engrave Ritchey tags.

Replacement spool for winding and unwinding portable fencing.

The base is made of high-impact plastic, and the clear glass jar allows you to see the feed levels without disturbing the bees. Little Giant Beehive Entrance Feeder is an easy-to-use plastic feeder that will fit directly into the front entrance of your...

Hardware not included. Install at convenient locations like fence corners and gates to switch off a section of fence for maintenance and routine checks. Stainless steel contacts.

Wind up or pay out your electric fence in minutes. Designed so it can be hung from a permanent fence wire or bolted to a post. Has a crank handle that operates like a ratchet for fence tension; will handle up to 1/2 mile of Bayguard.

If you would like to modify your existing VetGun to accept another CO2 cartridge size, an additional adaptor may be purchased separately. Be sure to order the CO2 cartridges that fit your gun.

Little Giant Ceramic Nest Eggs encourage hens to lay. They also help discourage chickens from pecking or eating eggs. Simply place them in a nesting box. They look and feel like the real thing, same echidna_color_options, size and weight.

One box is enough flyps for one cattle rub. Polyester orlon strips made to hang from rub.

Ideal to use with the Geared Medium Reel (#42522). Provides flexibility to liven the fence from either the reel or handle end.

Made from the same rot proof materials as the rub. Approximately 18" long with a metal ring at the top. Just the right size to suspend vertically in front of mineral feeders or in entry way of creep feeders.

Complete with gate handle, 2 tensioners and 20' tape.

This tightener is installed without having to disconnect the end of the fence. Not for use with coated wire. Can be tightened with a 1/2” drive ratchet. This powder-coated, white, aluminum tightener is best for use with rope or light-gauge wire.

Bolt measures 6” (measured from the 90 degree angle to the point of bolt.) Used with Hot Rope or polywire to turn corners or as an end insulator.